Concrete Cutting in Wilson, NC
Cutting concrete cleanly is about knowing what is inside it before the blade goes in. We saw cut slabs, walls and footings for doorways, trenches, plumbing runs and section replacement, with dust and slurry controlled and the cut lines straight enough that the patch or the frame drops right in.
Straight lines, controlled dust, nothing cut that should not be
The first job is knowing what is in the slab. Conduit, water and drain lines, radiant tubing and post-tension cables are all things that turn a routine cut into a very expensive day. We locate before we cut, and we will scan when the situation warrants it.
Then the cut itself. Walk-behind and hand saws for flatwork, wall sawing for openings, and core drilling for pipe and conduit penetrations. Cuts are snapped straight and taken full depth so the removal breaks along the line instead of tearing a ragged edge you have to patch twice.
- Utilities located before cutting
- Cut lines snapped straight and taken full depth
- Wet cutting or vacuum dust control indoors
- Slurry contained and disposed of properly
- Removal, loading and haul off included
- Doweled edges where a new pour will tie in
The cutting and removal work we do
Residential and commercial, indoors and out.
Doorways and openings
Wall sawing block and poured walls for doors, windows and pass-throughs, with the header and support coordinated first.
Trenches for plumbing
Slab trenching for drain, supply and conduit runs, cut to width, removed, and repoured after the rough-in passes.
Section replacement
Cutting out failed driveway, walk or floor panels along clean lines so the new pour has a square edge to bear on.
Core drilling
Cored holes for pipe, conduit, sleeves and drains through slabs, walls and footings.
Control and expansion joints
Joints cut in new or existing slabs on a planned layout, including retrofitting joints where none were cut.
Demolition and haul off
Breaking out, loading and hauling away the removed concrete, with the work area swept and left clean.
How we build your concrete cutting
On-site look
We look at the slab or wall, confirm what is inside it and around it, agree the cut lines, and price it in writing.
Locate and protect
Utilities located, cut lines snapped, dust and slurry containment set up and adjacent surfaces protected.
Cut and remove
Cut full depth on the line, then broken out, loaded and hauled off without damaging what stays.
Hand off or repour
Edges left square and doweled where a new pour follows, or the opening handed straight to your plumber or framer.
Jobs that start with a saw cut
Cutting is usually step one of somebody else's project. These are the calls we get.
A plumbing repair under a slab
A leak or a failed line under a slab floor needs a trench cut to it, and a clean repour after the plumber signs off.
Adding a door or window
A new opening in a block or poured wall needs a saw cut and a support plan, not a hammer and a hope.
Replacing one bad panel
A single cracked or settled driveway or walk panel comes out cleanly if it is cut on the joint lines first.
Lowering a floor
Converting a garage or a basement space to living area often means cutting out and lowering a section of slab.
New penetrations
Cores for a new drain, a conduit run, a dryer vent or a plumbing stack through an existing slab or wall.
Cracking with no joints
A slab poured without control joints can be retrofitted with cut joints to stop random cracking from spreading.
What separates a clean cut from an expensive one
Knowing what is inside. Slabs hold conduit, water lines, drain lines, radiant tubing and sometimes post-tension cables, and none of it is visible. We locate before cutting and we will bring in scanning where the risk justifies it, because the cost of finding out the hard way is many times the cost of checking.
Controlling dust and slurry. Dry cutting concrete indoors puts silica dust through the whole building. We wet cut or run vacuum dust collection, contain the slurry rather than letting it run into a drain or the yard, and dispose of it properly.
Cutting to a line. A cut that wanders or does not reach full depth tears out ragged and leaves you patching a bad edge. We snap the line, cut it full depth, and where a new pour follows we drill and set dowels into the existing slab so the two work together instead of separating at the seam.
What moves the price of concrete cutting
Cutting is priced by depth, length and how hard the location makes it.
Thickness and length
A 4 in residential slab and a 10 in commercial slab are different passes and different blade wear. Total cut length sets the rest.
Reinforcement inside
Heavily reinforced concrete, thick rebar mats and older aggregate-rich mixes all cut slower and consume blades faster.
Access and location
An open driveway is straightforward. Working inside a finished space, in a crawlspace, or overhead means containment, protection and hand equipment.
Removal and disposal
Breaking out, loading and hauling the concrete, plus slurry disposal, are priced with the cut rather than added later.
Cutting is quoted on site with the cut lines agreed and marked, the containment method stated, and removal and haul off included in the number.
What customers say about our concrete cutting
Why Wilson County calls us for concrete cutting
Located before cut
Utilities, tubing and tendons are identified before a blade goes in, not discovered by hitting them.
Dust and slurry controlled
Wet cutting or vacuum collection indoors, with slurry contained and disposed of properly.
Licensed and insured
Certificates available on request before work starts.
Where we pour concrete cutting
Based in Wilson, NC and working the counties around it. If your town is not on the list, ask and we will tell you straight whether we can get a crew to it.
Everything else we pour and repair
Same crew, same standard, whether it is a shed slab or a parking lot.
Concrete DrivewaysNew driveways, extensions and aprons formed, reinforced and finished to carry daily traffic.View service
Concrete PatiosPatios and extensions poured flat, drained away from the house and finished to spec.View service
Concrete Sidewalks & WalkwaysFront walks, side paths and connectors laid out straight with joints cut before they crack.View service
Stamped & Decorative ConcreteStamped patterns and integral or broadcast color, picked from real samples at the estimate.View service
Concrete Foundations & SlabsFootings, foundations and slabs on grade over a compacted stone base, with steel sized to the load.View service
Garage Floor ConcreteGarage slabs poured level to the door, with joints placed to control where movement goes.View service
Concrete Floor InstallationInterior floors for shops, additions and outbuildings, screeded flat and finished smooth.View service
Concrete Pool DecksPool surrounds with slip-resistant finishes and drainage pitched away from the water.View service
Concrete StepsPoured steps and landings formed to an even rise and run, tied into the walk or the porch.View service
Concrete Parking LotsCommercial pads, lots and drive lanes built for truck loads and laid out for drainage.View service
Foundation RaisingSettled foundations and slabs lifted back to level, with the cause addressed before the repair.View service
Concrete Repair and ReplacementCracked, settled or spalling concrete assessed first, then repaired or replaced with a reason given.View serviceConcrete Cutting questions we get in Wilson, NC
Yes. We use vacuum dust collection or wet cutting with containment, seal off the work area, and protect floors and finishes on the route in and out. It is not dust free, but it is manageable and we will tell you what to expect.
Ready to price your concrete cutting in Wilson, NC?
We come out, walk the job, and put the number in writing the same visit. Free, and no obligation.